| PRODUCTS |
 |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
CURRENT PROMOTIONS
 View Our Current Promotions »
|
Care Information
You are here: Decorator Tips » Care Information |
|
 |
Vanities
Clean timber with a damp cloth and dry. Vanities should not be exposed to excessive soap or water for long periods of time. Never rest soap directly on the vanity surface.
Granite & Marble Tops
Granite is the hardest of the natural stone countertop surfaces. Naturally resistant to acid, granite surfaces rarely etch making it an ideal counter top surface. HOWEVER, as with all natural stone surfaces, these materials are porous and therefore susceptible to absorbing discolouring spills or grease resulting in stains.
Marble, while elegant and beautiful, is more apt to spot, etch or dull over time when used in a bathroom. Marble is susceptible to acid attack from spills, personal care products and harsh cleaners. Acid etching, rings and water-spots that are found on marble are going to happen. Use marble polish to buff out etching and water spots or have the marble surface repaired and repolished.
Always clean the vanity top surface with a damp cloth, on a regular basis. Avoid the use of abrasive cleaners or products containing acids, vinegar or citrus juice to clean vanity tops. Use warm soapy water instead then a soft drying cloth.
Granite and marble are porous surfaces, which may stain if sufficient care is not taken. To avoid this simply wipe any spill immediately.
Sealers must be applied periodically depending on the wear and tear of the material and the porosity of the material, such as marble, granite or limestone.
Mirrors
When cleaning your new mirror, don’t spray cleaner directly onto the mirror - overspray can discolor the wood framing your mirror. Instead, spray the cleaner directly on the cleaning cloth and wipe mirror surface.
Porcelain
The easiest way to keep porcelain clean is to clean it once a week with water and an ordinary
all-purpose cleaner. DO NOT use any products that contain abrasives. Do not use caustic soda either, as it will damage the glaze.
Baths
Clean your bath using only a soft cloth and warm soapy water using a mild detergent. Rinse and wipe dry with a dry clean soft cloth. Avoid using harsh, abrasive, caustic and citrus based products as these will damage the surfaces.
Do not allow lime scale to build up on your bath - wipe it dry after use with a soft cloth. Make sure your taps don’t drip – dripping tap will cause discoloration of your bath and a build up of lime scale. Have taps re-washered when required, this will prevent staining from persistent dripping.
Shower Curtain Rails
To clean rails, DO NOT at any time use an abrasive powder, liquid cream, corrosive chemical cleaner or methylated spirits on any of the Recollections range of products. Always use a moist soft cloth to remove soapy residues. Regular wiping will prevent a build up of soap residue and grime. When entering or exiting your shower, NEVER hold onto a ceiling, or ceiling & side-mounted curtain rail for support as the hooks or fixtures can pull from the wall causing a fall hazard.
Toilet Suites
Mild detergents may be used when necessary to clean vitreous china products. Avoid caustic based cleaning products as they will scratch and dull the surface. Wipe any splashes of cleaner solutions from plastic or plated surfaces immediately. DO NOT use cistern blocks or in-tank toilet cleaners as they can damage the flush valve or other working parts.
Toilet Seats
Avoid using aerosol products. Do not allow abrasive chemicals and cosmetics (such as fingernail polish and aftershave) to come in contact with the toilet seat, as they can damage the finish. Painted wood seats require special care and cleaning. Use only mild detergents.
Heated Towel Rails
Remember to turn off the electrical supply before commencing cleaning. Wipe clean with a soft cloth using only non-abrasive and non-corrosive cleaning products. Do not damage the electrical supply cord.
Lighting
Before cleaning any lampshade or fixture, disconnect the power source (unplug from outlets).
To keep fixtures regularly clean, dust lightly every two or three months with a feather or wool duster.
All exterior lights receive a durable powder coat finish, which enhances the durability of the light. This finish should also be wiped down weekly with a soft, dry or damp cloth to remove the dust and debris that will accumulate on the surface. DO NOT use any abrasive cleaners or chemicals as this may damage the finish.
Switches & GPOs
To clean simply wipe with a damp cloth. Under no circumstances use abrasive cleaners (either liquid or powder) or solvent type cleaners on this range. Doing so may result in surface damage and tarnishing.
Doors
Doors should be checked periodically for signs of breakdown in the finish used. Over time all finishes break down, but the life of the finish will be determined largely by the doors location and exposure to the elements, and the quality of the finish selected.
Hardware
Hardware items should be wiped with a soft cloth and occasionally polished with a good non-abrasive wax following manufacturers directions. Never use abrasive cleaners, or polishes, on an item with a protective coating.
Remember, the nature of brass is to tarnish - the beauty of brass is that it can always be restored to its original finish. Breakdown of the lacquer coating, or natural tarnishing, to which brass is subject, in no way indicates a deterioration of the basic product.
Mantels
Wipe mantels with a soft damp cloth and dry. The occasional use of beeswax based furniture polish is recommended on the timber finish. Do not use a silicone based product. When cleaning mirrors, don’t spray cleaner directly onto the mirror. Overspray can discolour timber. Instead, spray the cleaner directly on the cleaning cloth and wipe mirror surface.
Fire Inserts
Our inserts are made from a very heavy, good quality casting and can be used to burn solid fuel (DO NOT use briquettes). When burning solid fuel, a new cast iron fireplace must be tempered by burning small fires initially (NEVER use chemicals or fluids to start the fire).
The insert requires installation into a masonry fireplace - always connect the unit to a chimney and never vent to another room or inside a building. Alternatively the insert can be used for decorative purposes only.
Regular dusting is sufficient to keep the insert clean. If required use a good quality stove polish to enhance the finish of the insert.
Outdoor
Metal (Iron) Cast and Formed Iron rusts. When washing use a mild detergent, scrub the surface gently and rinse with a low-pressure hose. Dirt, and dust on the surface will hold moisture against the paint, which will lead to premature failure of the coating. When you wash it, check for paint damage, and tell tale rust. If you catch this damage early, it can prevent a great deal of subsequent damage. Sand the rust off, along with the damaged paint, right down to bare metal, then prime, and paint with a rust-resistant paint. To keep your furniture in good condition, the first step is to keep it clean.
Stainless Steel is highly resistant to corrosion however it still requires some maintenance to preserve its finish. To maintain the finish of your stainless steel we recommend you use a suitable stainless steel cleaner, which cleans the stainless steel and leaves a fine layer of protective coating on the surface to help prevent the build up of contaminants.
Powder Coated Aluminium gives a high level of protection against the weather. However, in an outdoor environment dirt will collect on exposed surfaces of your aluminium furniture, which we recommend you clean with a suitable aluminium cleaner or clean it with a mild soap and water.
|
|
|
 |
| |
|
